menu "Power"

source "drivers/power/domain/Kconfig"

source "drivers/power/pmic/Kconfig"

source "drivers/power/regulator/Kconfig"

choice
	prompt "Select Sunxi PMIC Variant"
	depends on ARCH_SUNXI
	default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
	default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
	default AXP818_POWER if MACH_SUN8I_A83T || MACH_SUN50IW3
	default AXP1516_POWER if MACH_SUN50IW9
	default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8IW18

config SUNXI_NO_PMIC
	bool "board without a pmic"
	---help---
	Select this for boards which do not use a PMIC.

config AXP152_POWER
	bool "axp152 pmic support"
	depends on MACH_SUN5I
	select AXP_PMIC_BUS
	select CMD_POWEROFF
	---help---
	Select this to enable support for the axp152 pmic found on most
	A10s boards.

config AXP209_POWER
	bool "axp209 pmic support"
	depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
	select AXP_PMIC_BUS
	select CMD_POWEROFF
	---help---
	Select this to enable support for the axp209 pmic found on most
	A10, A13 and A20 boards.

config AXP221_POWER
	bool "axp221 / axp223 pmic support"
	depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
	select AXP_PMIC_BUS
	select CMD_POWEROFF
	---help---
	Select this to enable support for the axp221/axp223 pmic found on most
	A23 and A31 boards.

config AXP809_POWER
	bool "axp809 pmic support"
	depends on MACH_SUN9I
	select AXP_PMIC_BUS
	select CMD_POWEROFF
	---help---
	Say y here to enable support for the axp809 pmic found on A80 boards.

config AXP818_POWER
	bool "axp818 pmic support"
	depends on MACH_SUN8I_A83T || MACH_SUN50IW3
	select AXP_PMIC_BUS
	select CMD_POWEROFF
	---help---
	Say y here to enable support for the axp818 pmic found on
	A83T dev board.

config SY8106A_POWER
	bool "SY8106A pmic support"
	depends on MACH_SUNXI_H3_H5
	---help---
	Select this to enable support for the SY8106A pmic found on some
	H3 boards.

config AXP1516_POWER
	bool "axp1516 pmic support"
	depends on MACH_SUN50IW9
	select AXP_PMIC_BUS
	select CMD_POWEROFF
	---help---
	Say y here to enable support for the axp1516 pmic


endchoice


#config AXP_DCDC1_VOLT
#	int "axp pmic dcdc1 voltage"
#	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 3300 if AXP818_POWER || MACH_SUN8I_R40
#	default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
#	---help---
#	Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
#	disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
#	generic 3.3V IO voltage for external devices like the lcd-panal and
#	sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
#	save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
#	dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
#	powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
#
#config AXP_DCDC2_VOLT
#	int "axp pmic dcdc2 voltage"
#	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 900 if AXP818_POWER
#	default 1400 if AXP152_POWER || AXP209_POWER
#	default 1200 if MACH_SUN6I
#	default 1100 if MACH_SUN8I
#	default 0 if MACH_SUN9I
#	---help---
#	Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to
#	disable dcdc2.
#	On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
#	On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
#	On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
#	On A80 boards dcdc2 powers the GPU and can be left off.
#	On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
#	On R40 boards dcdc2 is VDD-CPU and should be 1.1V
#
#config AXP_DCDC3_VOLT
#	int "axp pmic dcdc3 voltage"
#	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 900 if AXP809_POWER || AXP818_POWER
#	default 1500 if AXP152_POWER
#	default 1250 if AXP209_POWER
#	default 1100 if MACH_SUN8I_R40
#	default 1200 if MACH_SUN6I || MACH_SUN8I
#	---help---
#	Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
#	disable dcdc3.
#	On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
#	should be 1.25V.
#	On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
#	On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
#	On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
#	On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
#	On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
#
#config AXP_DCDC4_VOLT
#	int "axp pmic dcdc4 voltage"
#	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 1250 if AXP152_POWER
#	default 1200 if MACH_SUN6I
#	default 0 if MACH_SUN8I
#	default 900 if MACH_SUN9I
#	---help---
#	Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
#	disable dcdc4.
#	On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
#	On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
#	On A23 / A33 boards dcdc4 is unused and should be disabled.
#	On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
#	On A83T boards dcdc4 is used for VDD-GPU.
#
#config AXP_DCDC5_VOLT
#	int "axp pmic dcdc5 voltage"
#	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
#	---help---
#	Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
#	disable dcdc5.
#	On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and
#	should be 1.5V, 1.35V if DDR3L is used.
#
#config AXP_ALDO1_VOLT
#	int "axp pmic (a)ldo1 voltage"
#	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 0 if MACH_SUN6I || MACH_SUN8I_R40
#	default 1800 if MACH_SUN8I_A83T
#	default 3000 if MACH_SUN8I || MACH_SUN9I
#	---help---
#	Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
#	disable aldo1.
#	On A31 boards aldo1 is often used to power the wifi module.
#	On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
#	On A80 boards aldo1 powers the USB hosts and should be 3.0V.
#	On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
#	should be 1.8V.
#
#config AXP_ALDO2_VOLT
#	int "axp pmic (a)ldo2 voltage"
#	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 3000 if AXP152_POWER || AXP209_POWER
#	default 0 if MACH_SUN6I || MACH_SUN9I
#	default 1800 if MACH_SUN8I_A83T
#	default 2500 if MACH_SUN8I
#	---help---
#	Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
#	disable aldo2.
#	On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V.
#	On A31 boards aldo2 is typically unused and should be disabled.
#	On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
#	On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
#	On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
#	On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
#	LPDDR2, and the codec. It should be 1.8V.
#
#config AXP_ALDO3_VOLT
#	int "axp pmic (a)ldo3 voltage"
#	depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 0 if AXP209_POWER || MACH_SUN9I
#	default 3000 if MACH_SUN6I || MACH_SUN8I
#	---help---
#	Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
#	disable aldo3.
#	On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
#	On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should
#	be 3.0V.
#	On A80 boards aldo3 is normally not used.
#	On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
#	3.0V.
#
#config AXP_ALDO4_VOLT
#	int "axp pmic (a)ldo4 voltage"
#	depends on AXP209_POWER
#	default 0 if AXP209_POWER
#	---help---
#	Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to
#	disable aldo4.
#	On A10(s) / A13 / A20 boards aldo4 should be 2.8V.
#
#config AXP_DLDO1_VOLT
#	int "axp pmic dldo1 voltage"
#	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 0
#	---help---
#	Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
#	disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
#	to power the ethernet phy. On A23, A33 and A80 boards this is often
#	used to power the wifi.
#
#config AXP_DLDO2_VOLT
#	int "axp pmic dldo2 voltage"
#	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 3000 if MACH_SUN9I
#	default 0
#	---help---
#	Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to
#	disable dldo2.
#	On A80 boards dldo2 normally powers the PL pins and should be 3.0V.
#
#config AXP_DLDO3_VOLT
#	int "axp pmic dldo3 voltage"
#	depends on AXP221_POWER || AXP818_POWER
#	default 0
#	---help---
#	Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
#	disable dldo3.
#
#config AXP_DLDO4_VOLT
#	int "axp pmic dldo4 voltage"
#	depends on AXP221_POWER || AXP818_POWER
#	default 0
#	---help---
#	Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
#	disable dldo4.
#
#config AXP_ELDO1_VOLT
#	int "axp pmic eldo1 voltage"
#	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 0
#	---help---
#	Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
#	disable eldo1.
#
#config AXP_ELDO2_VOLT
#	int "axp pmic eldo2 voltage"
#	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 0
#	---help---
#	Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
#	disable eldo2.
#
#config AXP_ELDO3_VOLT
#	int "axp pmic eldo3 voltage"
#	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
#	default 3000 if MACH_SUN9I
#	default 0
#	---help---
#	Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to
#	disable eldo3. On some A31(s) tablets it might be used to supply
#	1.2V for the SSD2828 chip (converter of parallel LCD interface
#	into MIPI DSI).
#	On A80 boards it powers the PM pingroup and should be 3.0V.
#
#config AXP_FLDO1_VOLT
#	int "axp pmic fldo1 voltage"
#	depends on AXP818_POWER
#	default 0 if MACH_SUN8I_A83T
#	---help---
#	Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
#	disable fldo1.
#	On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
#	used.
#
#config AXP_FLDO2_VOLT
#	int "axp pmic fldo2 voltage"
#	depends on AXP818_POWER
#	default 900 if MACH_SUN8I_A83T
#	---help---
#	Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
#	disable fldo2.
#	On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
#
#config AXP_FLDO3_VOLT
#	int "axp pmic fldo3 voltage"
#	depends on AXP818_POWER
#	default 0
#	---help---
#	Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to
#	disable fldo3.
#
#config AXP_SW_ON
#	bool "axp pmic sw on"
#	depends on AXP809_POWER || AXP818_POWER
#	default n
#	---help---
#	Enable to turn on axp pmic sw.
#
#config SY8106A_VOUT1_VOLT
#	int "SY8106A pmic VOUT1 voltage"
#	depends on SY8106A_POWER
#	default 1200
#	---help---
#	Set the voltage (mV) to program the SY8106A pmic VOUT1. This
#	is typically used to power the VDD-CPU and should be 1200mV.
#	Values can range from 680mV till 1950mV.
#
#config TWL4030_POWER
#	depends on OMAP34XX
#	bool "Enable driver for TI TWL4030 power management chip"
#	imply CMD_POWEROFF
#	---help---
#	The TWL4030 in a combination audio CODEC/power management with
#	GPIO and it is commonly used with the OMAP3 family of processors
endmenu